Freelance-Offers.com - Freelance Job Offers

We are looking for a electrical engineer that can design a magnetic stripe reader to read and record the magnetic data and then distribute over bluetooth when a client is connected. We also have a sub… (Budget: $750-1500, Jobs: Electronics, Embedded Software, Microcontroller, PCB Layout, Product Design)

we have two PCB’s from a machine which we need reverse engineered for a client abroad these two pcb’s will be required in a 1000 pc lot and we need them designed exactly as per the samples provided… (Budget: $250-750, Jobs: Electronics, Embedded Software)

Need a custom VGA camera solution with the following specs : 2Mp CMOS imaging sensor 30FPS - Specific sensor is given after bidding. inbuilt mpeg compression processor. on board high speed usb 2.0 controller with at least 2 usb ports… (Budget: $750-1500, Jobs: Electrical Engineering, Electronics, Embedded Software, Microcontroller, PCB Layout)

I would like a small program written for Atmel USB microcontroller ported over to use on an SX or PIC device. (Budget: $30-250, Jobs: C Programming, Electronics, Microcontroller)

Update logo and design for softwareqaworld.com site. (Budget: $250-750, Jobs: Electronics, Logo Design, Verilog / VHDL)

The project is Nonpublic. Description can be read only by registered users. (Budget: $30-250)

You will be making a small portable magnetic reader that runs off a battery and has similar dimensions to 4 x 5 x 15mm . This magnetic card reader collects/stores tracks 1 and 2 on its 2mags of onboard memory… (Budget: $30-250, Jobs: Electrical Engineering, Electronics, Microcontroller, PCB Layout, Project Management)

On a local 10/100 base Network I need to send 8 Channels of uncompressed audio 96k-24bits provided from a Analog Devices ADAU1401A in TDM format (serial I2S stream of 8 Channel of audio 96k 32bits) from… (Budget: $250-750, Jobs: C Programming, Electronics, Microcontroller, PCB Layout)

I require a circuit and layout of PCB to allow 24 channel TTL Digital I/O from an embedded SBC to drive 250v power relay which can be situated up to 20m away. (Relay specs can be found at the following website: http://www.scr.com.tw/ssr-series_01.htm )… (Budget: $250-750, Jobs: Electronics, PCB Layout)

The project is Nonpublic. Description can be read only by registered users. (Budget: $30-250)

Looking for an engineer to design and build a proto of a long range Transmitter and receiver. Range: ~800 meters- Must be designed so that I do not need a FCC license… Transmitter– size:… (Budget: $250-750, Jobs: Electrical Engineering, Electronics, Engineering, Microcontroller, PCB Layout)

I have a DC solar pump that operates directly on solar panels at 70 VDC / 13 Amps. I need a power supply design for two different power supplies. Power supply 1: Output is DC 70 volts with standard 120 VAC input… (Budget: $30-250, Jobs: Electrical Engineering, Electronics, PCB Layout)

I have researched a lot about this, I am not a programmer thats the only problem, exactly what i need is i want to start/Stop or see status of my Sprinklers at my home or office . The sprinkler is just an example to keep it simple… (Budget: $750-1500, Jobs: C Programming, Electronics, Engineering, Manufacturing, Product Design)

I need a person that can take my idea from a hand drawn representation to a working model. I have an idea for a new remote control, but I need to put together a engineering drawing so that I may get a… (Budget: $250-750, Jobs: Electrical Engineering, Electronics, Microcontroller)

The FPGA project is to porting a WLAN s PHY cores into a Xilinx FPGA development board (E.g Spartan 3A). Use of the public domain WLAN s PHY cores from Rice University s WARP project (http://warp.rice.edu/trac/wiki/OFDMReferenceDesign/Changelog),… (Budget: $250-750, Jobs: Electronics, Engineering, Matlab Mathematica, Verilog / VHDL, Wireless)

The project is Nonpublic. Description can be read only by registered users. (Budget: $30-250)

I need to develop a gsm enabled standalone biometric attendance system. For this, I am planning to integrate Suprema SFM3500 fingerprint module with a gsm enabled board. Board can be Win CE or linux based… (Budget: $250-750, Jobs: Electronics, Embedded Software)

I need someone to do a pcb layout of a LED matrix display 16 x 16 the leds are 10mm and the have to be 10mm appart from eachother, it will be driven by four 74hc595 SMD 2 ULN2803 and controlled via SPI… (Budget: $30-250, Jobs: CAD/CAM, Electronics, Engineering, Microcontroller, PCB Layout)

Need to interface 2 boards with Analog-Devices ADAU1401A and establishing a point to point connection via a TCP/IP connection. The project should: - Provide source code in C with all necessary files… (Budget: $30-250, Jobs: C Programming, Electronics, Microcontroller)

You will be making a small portable magnetic reader that runs off a battery. This magnetic card reader collects/stores tracks 1 and 2 on its 2mags of onboard memory. The magnetic head and magnetic stripe will be ISO… (Budget: $1500-3000, Jobs: Electrical Engineering, Electronics, Microcontroller, PCB Layout, Project Management)